GLOSSARY / MANUFACTURER DIRECT
Selective coordination is a protection goal: for a fault or overload, the overcurrent device closest to the affected circuit should open, while upstream devices remain closed when the system design and fault conditions allow. That can limit an interruption to one branch rather than a larger portion of a facility. It is not established by breaker labels, amperage alone, or a general claim that devices are coordinated. Buyers need device-specific data and a study of the actual system. Switchgear Builder Virginia can build new switchgear to project requirements; device selection, settings, and coordination must be defined and verified for the application.
What the term means
An overcurrent protective device (OCPD), such as a circuit breaker or fuse, responds when current exceeds conditions it is designed to handle. In a selectively coordinated system, the device serving the faulted branch is intended to clear that overcurrent before an upstream device opens, within the conditions evaluated. The practical objective is to keep unaffected loads energized when possible, not to promise that every fault will affect only one circuit. A fault may be large enough, or outside the evaluated range, for more than one device to operate. “Nearest” means electrically closest along the path from the source to the fault, not necessarily physically closest inside a lineup. The required boundaries and operating conditions depend on the project. A useful definition therefore includes both the intended isolation and the need to verify that the selected devices can achieve it together.
Why it matters
When an upstream main or feeder device opens for a downstream branch fault, multiple loads can lose power even if the fault is confined to one circuit. Selective coordination seeks to reduce that reach of an interruption, which may matter where continuity supports essential operations, process stability, or safe orderly shutdown. It can also help operators locate the affected section more narrowly, although it does not eliminate troubleshooting or restore power automatically. The value depends on what loads share each protective device and what interruption the owner can tolerate. A design that maximizes selectivity in every circumstance may conflict with other protection goals, equipment limits, or project requirements. Buyers should identify critical loads and the portions of the distribution system that need to remain in service, then have the responsible electrical design professional determine the applicable criteria. Coordination is one design objective, not a substitute for sound protection or maintenance.
Why device data matters
Protective devices cannot be assessed by frame size or trip rating alone. Relevant information may include manufacturer and exact catalog number, trip-unit type, available settings, fuse class, interrupting capability, and the device’s published time-current or selectivity data. Two breakers with similar ampere ratings may respond differently, and adjustable trip settings can change the relationship between upstream and downstream operation. The available fault current at each point also matters: selectivity at one current range does not by itself establish selectivity across every possible fault level. The reviewing engineer needs accurate system details and the actual devices proposed, not generic curves chosen as placeholders. Manufacturer data may identify limits or combinations for which selectivity is specified; those conditions should be checked against the project. A coordination statement without device-specific support can hide important boundaries, especially during procurement substitutions or later setting changes.
What a study checks
A coordination study models the source and distribution path, estimates available fault current at relevant locations, and compares protective-device operating characteristics. Engineers commonly review time-current curves, device settings, and manufacturer selectivity information to see whether downstream devices operate ahead of upstream devices over the required range. The study inputs must match the design: transformer and source data, conductor impedances, device types, trip-unit options, and proposed settings can all affect conclusions. The study may identify ranges where coordination is achieved and ranges where it is not, rather than deliver a blanket yes-or-no label. Requirements also depend on the project’s adopted codes and application; the design professional should establish what must be coordinated. If equipment, source conditions, or settings change, the study may need review. Keep the study and final settings aligned with the equipment actually furnished and installed. Device coordination depends on their specific characteristics, not a universal breaker hierarchy. ([docinfofiles.nfpa.org](https://docinfofiles.nfpa.org/files/AboutTheCodes/70/70_A2025_NEC_P13_FD_PIResponses.pdf))
Specify it for new gear
For a new switchgear quote, provide the one-line diagram, system voltage, available source and fault-current information, load priorities, and the study criteria established by the project engineer. Identify required device manufacturers or approved alternatives, trip-unit functions, adjustability, and any documented selectivity limits that affect the design. These choices involve tradeoffs: a device combination that supports greater selectivity under specified conditions may affect cost, space, settings, or available equipment choices. Do not assume that changing one breaker or trip setting is a harmless substitution; have the responsible professional check the coordination and protection consequences. Switchgear Builder Virginia manufactures new equipment in the USA using all-American components and offers custom builds and nationwide shipping; schedules and ratings are confirmed for each quote. UL 891 assemblies may be applicable to low-voltage switchboards, but that does not establish coordination or apply to medium-voltage gear. Verify project requirements and equipment documentation before approval.
