AMERICAN BUILT. PROJECT READY.MANUFACTURER DIRECT (951) 403-5738
Gray switchgear and electrical conduit in an industrial work area.

APPLICATIONS / VIRGINIA & NATIONWIDE

Peak Shaving Source Integration

New American-built power distribution equipment, engineered around your project.

ENGINEERED FOR POWER
US
Made in the USAAmerican components
✓
Project-specific standardsConfirmed for equipment type
↗
Built to moveLead time quoted by project

APPLICATIONS / MANUFACTURER DIRECT

Peak shaving source integration starts with a measurable demand objective and an electrical design that fits the facility’s operating plan. A generator or energy storage system may support the strategy, but its connection, operating mode, and controls must be defined before anyone can estimate demand reduction. Switchgear Builder Virginia manufactures new custom switchgear in the USA using all-American components, with nationwide shipping. Equipment configuration, ratings, schedule, and expected performance depend on project information and verification. The discussion below outlines the decisions buyers should resolve before requesting a design or estimate.

Define the Demand Objective

Begin by identifying what the facility wants peak shaving to accomplish. The objective might be reducing a measured demand peak, limiting a utility-meter interval, managing a site load limit, or reserving capacity for another operating need. These goals are not interchangeable: the measurement point, time interval, and acceptable response can change the control strategy and equipment interfaces. Provide available demand history, expected load changes, operating hours, and any known limits or targets. A target alone does not establish achievable savings; results depend on load behavior, source capacity, dispatch logic, and applicable utility arrangements. Also clarify whether the system should respond automatically, require operator action, or support both modes. Switchgear Builder Virginia can use this information to scope a new custom assembly, but performance projections require project-specific data and review. Avoid treating a nameplate rating as proof of demand reduction.

Choose the Source Interface

A generator and an energy storage system present different interface questions. For a generator, identify available electrical data, expected operating duty, starting and synchronization requirements, and any restrictions on operation. For storage, provide inverter output characteristics, charging and discharging limits, energy capacity, and the intended operating window. Confirm whether the source equipment is part of the project scope or supplied separately, and identify who is responsible for interface drawings and controls coordination. The switchgear design may need provisions for source connections, sensing, isolation, protection, or control signals, but each item must be specified and verified rather than assumed. Equipment ratings and configuration depend on system voltage, fault-current information, load conditions, and the complete source arrangement. Early coordination helps reveal missing inputs before the design is developed; it does not establish that any particular source or operating feature is included.

Select Transfer or Paralleling

Decide whether the operating concept calls for transfer between sources or for paralleling them. A transfer arrangement moves designated loads from one source to another under a defined sequence; a parallel arrangement allows sources to operate together only when the system design and required approvals support that mode. The choice affects protection coordination, interlocking, metering, control responsibilities, and the information needed from source vendors. State whether interruption is acceptable, which loads are in scope, and what conditions should initiate or end source operation. Do not assume that a generator, inverter, or switchboard supports closed-transition transfer or parallel operation simply because it is present. Those capabilities and any required approvals must be confirmed for the specific project. For applicable low-voltage switchboards, UL 891 assemblies may be considered where appropriate; applicability and assembly details require verification.

Specify Controls and Signals

Controls translate the demand objective into operating decisions, so define their boundaries clearly. Identify the source controller, switchgear control functions, facility or building-management interface, and the party responsible for each signal and sequence. Useful inputs may include demand measurement, source availability, breaker status, alarms, and operating limits, but the actual signal list depends on the selected equipment and control design. Describe priorities during normal operation, peak response, source failure, communications loss, and return to the preferred source. Ask how operators will see system state and acknowledge alarms, while leaving detailed settings and safety procedures to qualified project personnel. Provide available control diagrams, protocol requirements, and vendor documentation early. A proposed feature is not an included feature until it appears in the reviewed scope. Control behavior, protection coordination, and any required testing should be documented and verified before commissioning.

Provide Data Before Estimating

A useful estimate requires more than a demand target. Share one-line diagrams, system voltage, available fault-current information, load schedules, source equipment data, site constraints, and the intended transfer or paralleling sequence. Include metering details and the demand interval or limit the strategy is meant to address. Note future expansion, space constraints, environmental conditions, and coordination responsibilities when known; these can affect enclosure, layout, interfaces, and design review. Identify required standards, inspections, approvals, and testing for the project, then verify which apply to the proposed equipment and jurisdiction. Switchgear Builder Virginia manufactures new custom equipment in the USA from all-American components and offers short lead times, but schedule and ratings remain subject to quote and verification. Nationwide shipping is available. Expected demand results cannot be responsibly estimated until operating assumptions, source capabilities, and site data have been reviewed.

Related project guides

START A CONVERSATION

Let’s build the right solution.

Tell us what you’re building, replacing or upgrading. Share the information you have now; project details and availability can be confirmed together.

PREFER TO TALK?

(951) 403-5738

Virginia projects. Nationwide delivery.

This attempts to open a draft in your configured email app; review and send it there. Browser support varies. For immediate assistance, call (951) 403-5738.

Request a quote