AMERICAN BUILT. PROJECT READY.MANUFACTURER DIRECT (951) 403-5738
Gray switchgear beneath overhead electrical conduits in an industrial room.

FAQ / VIRGINIA & NATIONWIDE

How Do I Specify Switchgear Voltage?

New American-built power distribution equipment, engineered around your project.

ENGINEERED FOR POWER
US
Made in the USAAmerican components
✓
Project-specific standardsConfirmed for equipment type
↗
Built to moveLead time quoted by project

FAQ / MANUFACTURER DIRECT

To specify switchgear voltage, start with the nominal voltage at the point where the equipment will connect, then document the system configuration and the loads it must serve. For medium-voltage equipment, identify the required equipment voltage class separately; it is not simply another way to state operating voltage. The utility, engineer, and equipment manufacturer should confirm compatibility before the design is finalized. These details help Switchgear Builder Virginia evaluate a new custom build without relying on assumptions from a project name or an old equipment label.

Start With Service Voltage

State the nominal service voltage where the switchgear will connect, and identify whether that value is measured phase-to-phase, phase-to-neutral, or both. A number without that context can describe different systems, so include the project’s one-line diagram or a utility service document when available. If the service is not yet confirmed, mark the voltage as preliminary and identify who will verify it. Do not infer the required voltage from a building name, an existing enclosure, or a nearby piece of equipment; those may not represent the connection being designed. Ask the engineer or utility to resolve discrepancies before equipment selection. Also distinguish the incoming service from any downstream voltage supplied through transformers. Clear source information gives the manufacturer a sound basis for reviewing the proposed configuration, while an unverified assumption can affect equipment selection, connections, and the overall design.

Specify Phase and Wiring

Along with voltage, state the number of phases and the intended wire configuration, such as three-phase, three-wire or three-phase, four-wire, if confirmed for the project. Identify whether a neutral is required at the switchgear and how it will be used; do not assume that a neutral is present just because some loads need one. Include the expected source arrangement and grounding information when the project documents establish them, and ask the electrical engineer to clarify anything uncertain. These details help distinguish systems that may share a nominal voltage but need different connections or internal arrangements. They also help the manufacturer understand whether the equipment must serve line-to-line loads, line-to-neutral loads, or both. Keep the service description consistent across the one-line diagram, equipment schedule, and request for quotation, and flag any conflicts for review rather than choosing one value by guesswork.

For Medium Voltage

For a medium-voltage application, specify both the nominal system voltage and the equipment voltage class required by the project. These are related but not interchangeable: the class identifies the equipment’s intended voltage range and insulation design, while nominal voltage describes the system. Have the engineer and serving utility confirm the applicable class and system details; do not select a class from a voltage number alone. The design team may also need to establish grounding method, frequency, insulation coordination, and other project-specific requirements. Provide those as documented requirements, not assumptions, and identify open items in the inquiry. Equipment voltage class is not a substitute for checking compatibility with the actual service and connected system. This topic concerns medium-voltage equipment; UL 891 is a standard for applicable low-voltage switchboards and should not be used to describe medium-voltage switchgear.

Check the Whole System

Compare the voltage information at the source with the requirements of transformers, motors, drives, generators, and other connected equipment. A project may include several voltage levels, so label each one and show where a transformer or other conversion point separates them. Specify which voltage applies to the switchgear being requested, not merely the voltage of a downstream load. If the design includes alternate sources or future expansion, document those operating arrangements for engineering review rather than expecting a single voltage value to describe them. Ask the responsible engineer to reconcile the one-line diagram, load information, equipment schedule, and utility data before the purchase specification is released. This review can reveal mismatched assumptions early, when the design can still be clarified. It does not replace detailed coordination or prove that a proposed assembly is suitable; final configuration and ratings must be evaluated against verified project requirements.

Prepare the Request

A useful request for quotation identifies the connection point, nominal voltage, phase, wire configuration, frequency if established, and—in medium-voltage work—the required equipment voltage class. Attach the latest one-line diagram and schedule, identify the documents’ revision dates, and list unresolved utility or engineering questions. If project information may change, label it preliminary so the quotation review can identify what needs confirmation. Switchgear Builder Virginia manufactures new custom switchgear in the United States using all-American components and ships nationwide; final configuration, applicable ratings, schedule, and lead time are subject to review and quotation. Do not treat a preliminary description as approval of an equipment rating. Ask the manufacturer to review the submitted requirements and identify any missing information before design proceeds. The responsible project professionals must confirm the service and design requirements before the final equipment specification is accepted.

Related project guides

START A CONVERSATION

Let’s build the right solution.

Tell us what you’re building, replacing or upgrading. Share the information you have now; project details and availability can be confirmed together.

PREFER TO TALK?

(951) 403-5738

Virginia projects. Nationwide delivery.

This attempts to open a draft in your configured email app; review and send it there. Browser support varies. For immediate assistance, call (951) 403-5738.

Request a quote