GLOSSARY / MANUFACTURER DIRECT
A bus tie is a device or connection that links two bus sections, allowing them to operate separately or, when the design and operating plan permit, together. The term describes the connection’s role, not one universal arrangement: equipment, controls, and operating procedures vary by system. For a new switchgear project, the useful questions are what each section supplies, which sources can feed it, and what conditions must be met before the tie changes state. Those answers shape the one-line diagram, equipment configuration, and coordination review.
What the Tie Connects
A bus is a conductive assembly that distributes electrical power to connected circuits. In a switchgear lineup divided into two sections, a bus tie connects one section’s bus to the other. The tie may be implemented with a circuit breaker, switch, or another arrangement selected for the system; “bus tie” names its function, not a single standard piece of hardware. With the tie open, the sections are electrically separated at that point. With it closed, the sections are connected, subject to the rest of the system’s configuration. This basic definition helps distinguish the tie from a feeder, which carries power to a load or downstream equipment, and from an incoming source connection. A project drawing should show the tie’s position and related sources and loads clearly, so reviewers can understand what the connection can affect.
Why Operating State Matters
The tie’s state—open or closed—changes which bus sections are connected and can affect how power reaches loads. A normally open tie can keep sections separated during ordinary operation, while a planned transfer may use the connection to supply a section from another available source. A normally closed arrangement keeps sections interconnected during its intended operating condition. Neither state is automatically better: the choice depends on the one-line diagram, source capabilities, protection design, operating objectives, and applicable project requirements. A closed tie does not create additional power capacity; it connects buses, and the connected sources and equipment still set system limits. Buyers should define normal and alternate states, expected switching scenarios, and loads that must remain supplied. These details let the design team evaluate a proposed arrangement rather than assume a tie will work the same way in every installation.
Coordinate Sources and Protection
When a bus tie closes, sources on separate sections may become electrically connected. The design review therefore needs to consider whether those sources are intended and permitted to operate in parallel, and under what conditions. If parallel operation is not intended, the control scheme and operating procedure may need to prevent closing the tie while both sources are connected. Protection settings and device selection also require coordination with the available sources, connected loads, and system fault conditions. A tie can change fault-current paths and which protective devices respond, so evaluating it in isolation from the rest of the distribution system is not enough. The project engineer should establish the required operating sequence and confirm that the drawings, protective-device coordination, and control logic agree. Equipment details and ratings must be verified for the actual application; a generic bus-tie definition cannot establish them.
Specify the Project Clearly
When requesting a new lineup, provide a one-line diagram or a clear description of the two bus sections, their incoming sources, and the loads they serve. Identify the intended normal state of the tie and describe any transfer conditions, including whether source paralleling is allowed. Note the operating method required by the project, such as local or remote operation, if applicable, and identify control or interlocking requirements for engineering review. Also share the system voltage, available fault information, site constraints, and applicable project specifications, while treating final equipment ratings as items to verify. These inputs help the manufacturer develop a configuration for the actual duty instead of selecting a tie based on its name alone. Switchgear Builder Virginia manufactures custom new equipment in the USA using all-American components; the project scope, schedule, and ratings remain subject to quotation and verification.
Review Before Release
Before approving a bus-tie arrangement, check that the one-line diagram matches the intended operating plan and that each source and bus section is identified consistently. Confirm who is responsible for engineering the protection and control details, and have the project’s qualified design professionals review switching conditions and interlocking requirements. Verify that the proposed device and bus arrangement suit the stated system conditions; do not infer a rating, listing, test, or approval from the phrase “bus tie.” For applicable low-voltage switchboard assemblies, UL 891 requirements may be relevant and should be confirmed for the specific project. Other equipment types and project requirements need their own review. Switchgear Builder Virginia can quote a custom new assembly for nationwide shipping, with schedule and configuration confirmed during the project process. Clear documentation helps buyers compare proposals on the same operating assumptions and identify open technical decisions before equipment release.
