AMERICAN BUILT. PROJECT READY.MANUFACTURER DIRECT (951) 403-5738
Three switchgear cabinets on pallets, with the left cabinet door open.

GLOSSARY / VIRGINIA & NATIONWIDE

What Is Available Fault Current?

New American-built power distribution equipment, engineered around your project.

ENGINEERED FOR POWER
US
Made in the USAAmerican components
✓
Project-specific standardsConfirmed for equipment type
↗
Built to moveLead time quoted by project

GLOSSARY / MANUFACTURER DIRECT

Available fault current is the prospective short-circuit current that could flow at a particular point in an electrical system if a fault occurred. It is a calculated or otherwise established system value, not the amount of current a switchboard normally carries. For a new equipment project, Switchgear Builder Virginia considers this value alongside the equipment configuration and protective-device ratings. The required values and applicable construction details must be confirmed for the specific project before selection or quotation.

The fault-current value

Available fault current describes the current a power source and connected electrical system could deliver to a specific point during a short circuit. The value depends on the source and the electrical path to that point, including factors such as transformer characteristics, conductor impedance, and system configuration. It is prospective: it estimates the current that could flow under the stated conditions, rather than measuring ordinary operating current or predicting what will flow after protective devices respond. Because the electrical path changes from one location to another, a value established at one point should not automatically be applied elsewhere. Engineers determine or obtain the value using project-specific system information and accepted calculation methods. The resulting figure helps define the fault duty that equipment at that location may need to withstand or interrupt, depending on the equipment and its role. It is one input to equipment selection, not a complete specification by itself.

Compare ratings carefully

Available fault current must be compared with the applicable short-circuit ratings of the equipment and the ratings of its protective devices. These ratings describe different duties, so a single number on a submittal should not be treated as proof that every component is suitable. For example, a protective device’s interrupting rating concerns its ability to interrupt fault current under specified conditions. Equipment short-circuit withstand or assembly ratings address the assembly’s ability to withstand fault effects, often in coordination with the protective device and its clearing time. The relevant rating terminology and permitted combinations depend on the equipment design and applicable standards. The project engineer and equipment supplier should verify the fault-current value at the installation point, the ratings shown for the proposed configuration, and any conditions attached to those ratings. If the available current exceeds an applicable rating, the selection or system design needs further review before approval.

Why the location matters

A facility can have different available fault-current values at different points in its distribution system. Current generally encounters different impedance as it travels from the source through transformers, conductors, and equipment, so the value at a service entrance may differ from the value at a downstream panel or switchboard. Changes to the system can also affect the calculation: a transformer replacement, revised conductor routing, added source, or operating configuration may alter the fault duty. Buyers should therefore provide project-specific electrical information and identify the equipment location rather than relying on a value copied from an unrelated drawing or an earlier project. When information is incomplete or the system has changed, the responsible electrical professional should determine whether calculations need updating. A location-specific value supports a more meaningful comparison with the proposed equipment and helps avoid selecting a design based on assumptions that no longer match the installation.

Protective-device coordination

Protective devices are part of the fault-current evaluation, but their presence does not by itself establish that an assembly is suitable. A fuse or circuit breaker may limit or interrupt fault current, while the equipment rating and the protective device’s characteristics must be considered together under the applicable conditions. Relevant details can include the device type, rating, trip or clearing behavior, and the specific equipment combination evaluated for the project. Buyers should ask which device and configuration support a stated assembly rating and whether substitutions would change that basis. Do not assume that a higher-rated protective device, a different model, or a faster trip setting automatically makes an otherwise unsuitable assembly acceptable. The project’s engineer, manufacturer, and reviewing authority may need to resolve rating and coordination questions using current project documents. Verify the final device schedule and assembly details against approved submittals before equipment is released or installed.

Project review and ordering

For a new low-voltage switchboard project, provide the available fault-current information at the proposed connection point, along with voltage, service arrangement, distribution requirements, and the protective-device details known at design stage. Switchgear Builder Virginia can use the supplied project requirements to develop a custom build; schedules, ratings, and configuration remain subject to quote and verification. If applicable, the project may call for a UL 891 assembly, but that standard does not replace the need to confirm fault-current suitability or every device rating. Ask the electrical engineer or other responsible project professional to verify the system value and applicable design criteria, and have proposed equipment documentation checked against them. If the source or system arrangement is still being finalized, flag that uncertainty early. A confirmed, location-specific value and a clearly defined device configuration give buyers and reviewers a sounder basis for evaluating proposed equipment.

Related project guides

START A CONVERSATION

Let’s build the right solution.

Tell us what you’re building, replacing or upgrading. Share the information you have now; project details and availability can be confirmed together.

PREFER TO TALK?

(951) 403-5738

Virginia projects. Nationwide delivery.

This attempts to open a draft in your configured email app; review and send it there. Browser support varies. For immediate assistance, call (951) 403-5738.

Request a quote