AMERICAN BUILT. PROJECT READY.MANUFACTURER DIRECT (951) 403-5738
Gray switchgear and electrical conduit in an industrial work area.

TECHNICAL GUIDES / VIRGINIA & NATIONWIDE

Device Coordination Curves

New American-built power distribution equipment, engineered around your project.

ENGINEERED FOR POWER
US
Made in the USAAmerican components
✓
Project-specific standardsConfirmed for equipment type
↗
Built to moveLead time quoted by project

TECHNICAL GUIDES / MANUFACTURER DIRECT

Device coordination curves help engineers compare how protective devices respond to current over time. Reading them can reveal whether a downstream device is expected to clear a fault before an upstream device operates, while also showing where the curves overlap or leave little separation. They are study tools, not a substitute for verified equipment data or an engineer’s review. Switchgear Builder Virginia manufactures new custom switchgear in the USA using all-American components, with nationwide shipping and short lead times subject to project requirements and quote verification. The page title is Device Coordination Curves, and its guide slug is guides-device-coordination-curves.

What the curves show

A time-current curve plots current against operating time for a protective device. The horizontal axis usually uses a logarithmic scale for current, and the vertical axis shows time, also commonly on a logarithmic scale. A device’s plotted band may represent a range rather than one exact trip point because operating behavior can vary with current, tolerances, and the device’s characteristics. To compare devices, engineers place their curves on the same plot and check how their operating regions relate across relevant fault-current levels. A curve does not, by itself, establish that a system is coordinated. The engineer must also confirm the actual device type, trip unit, settings, and available fault current. For switchgear selection, provide project-specific electrical data so proposed equipment can be evaluated against the study and the intended operating conditions.

Upstream and downstream devices

In a typical distribution path, a downstream protective device serves a branch or load, while an upstream device protects a feeder or source connection. Coordination aims to have the downstream device clear a fault in its zone before the upstream device trips, when the design objective and device behavior permit. On a curve plot, engineers compare the devices’ operating bands at the currents expected at each point in the system. Separation between bands may support selective operation over a defined range, but overlap can indicate that both devices could respond. The outcome depends on actual fault current, device tolerances, settings, and the study criteria; labels such as “main” and “branch” do not prove coordination. A project engineer should identify which loads require continuity and define acceptable clearing behavior before equipment is specified or settings are selected.

Reading overlap and limits

Curve separation is not equally meaningful at every current. At lower overload levels, long-time settings may govern; at higher fault currents, short-time, instantaneous, or current-limiting behavior may dominate, depending on the selected devices. Some manufacturer data is shown as a band, and published curves may not capture every interaction or installation condition. Engineers therefore review the full range relevant to the system rather than judging coordination from one point or a visually tidy plot. They also check whether the study’s assumptions match the proposed equipment and protective-device options. If curves overlap, that does not alone explain the consequence: the engineer must assess the system, required selectivity, and device characteristics. Do not treat generic example curves as approved settings. Actual selections require verified product data and an engineer-led study for the specific installation.

Information for a study

A useful coordination study begins with a current one-line diagram and the project’s source and load information. The engineer may need utility or generator data, transformer details, conductor and cable information, equipment ratings, and the protective-device models and trip-unit options under consideration. Available fault current and operating configurations matter because a system can have different conditions with alternate sources or ties open and closed. The owner or design team should state its coordination objectives, critical loads, and any requirements for arc-flash analysis or other related evaluations. Missing or preliminary inputs should be identified, not silently replaced with assumed final values. These details help equipment proposals reflect the design basis without implying that a particular rating or setting has already been established. Switchgear Builder Virginia can use project requirements to develop a custom new-equipment scope, subject to engineering review and quote verification.

Applying study results

After the engineer evaluates the system, the study documentation can identify device selections, proposed settings, assumptions, and coordination limits. The project team should reconcile those results with the equipment submittal and confirm that the supplied device configuration matches the reviewed design. If a device, source, transformer, or system arrangement changes, the engineer may need to reassess the curves and conclusions. Settings should be implemented and verified by qualified personnel under the project’s approved procedures; this guide is not an instruction for live adjustment or field testing. For low-voltage switchboards, UL 891 assemblies may be applicable, but applicability and requested construction must be confirmed for the project. Ratings, features, testing, and approvals remain subject to verification and quote. Switchgear Builder Virginia manufactures new custom switchgear in the USA, with short lead times subject to the confirmed scope and nationwide shipping.

Related project guides

START A CONVERSATION

Let’s build the right solution.

Tell us what you’re building, replacing or upgrading. Share the information you have now; project details and availability can be confirmed together.

PREFER TO TALK?

(951) 403-5738

Virginia projects. Nationwide delivery.

This attempts to open a draft in your configured email app; review and send it there. Browser support varies. For immediate assistance, call (951) 403-5738.

Request a quote