TECHNICAL GUIDES / MANUFACTURER DIRECT
Medium-voltage protection zones define which equipment a protective scheme is intended to detect and isolate when a fault occurs. Their boundaries depend on the one-line diagram, instrument-transformer locations, relay functions, and the project’s operating goals—not simply on compartment names. Switchgear Builder Virginia manufactures new, custom switchgear assemblies in the USA using all-American components, with schedules and ratings subject to quote and verification. This guide outlines decisions owners, engineers, and project teams should coordinate before specifying a lineup. Final protection design, settings, and equipment suitability require project-specific engineering review.
Define Each Zone
A protection zone is a defined portion of an electrical system monitored by a protective scheme. Typical medium-voltage zones may cover a transformer, a bus section, or an outgoing feeder, but the exact boundaries depend on the one-line diagram and the sensing points. Start by identifying the equipment each zone should protect, the breakers or other devices expected to isolate it, and which adjacent equipment remains energized after a trip. A clear zone map helps reveal gaps, unintended overlap, or a trip that would interrupt more loads than intended. It also gives the engineer, owner, and switchgear manufacturer a shared basis for reviewing compartment arrangement and control interfaces. The manufacturer can build to verified project requirements; it does not replace the protection engineer’s responsibility to define the scheme or approve its application.
Place Current Transformers
Current transformers (CTs) provide relay inputs and help establish where a scheme can detect current. Their proposed locations should be shown on the one-line and coordinated with breaker positions, bus connections, and equipment terminals. For adjacent zones, engineers commonly review whether the CT coverage overlaps enough to avoid an unprotected gap, while also checking how a fault in that overlap will be detected and cleared. CT ratio, accuracy, burden, polarity, wiring, and physical arrangement are application-specific items to verify; a ratio selected from load current alone may not suit every protective function. The switchgear design must accommodate the specified CTs and secondary wiring where included in scope. Confirm who supplies each CT, who checks its application, and how terminal points are documented. Final choices belong in the approved design documents, not in an unverified catalog assumption.
Separate Bus and Feeder Zones
A bus zone and a feeder zone serve different purposes. Bus protection is intended to detect faults on a defined bus section, while feeder protection addresses faults on an outgoing circuit within the scheme’s reach. Section breakers, tie breakers, and CT positions can affect which devices must operate and whether an event removes one section or more of the lineup. Do not infer the protection boundary from a switchgear nameplate or a drawing symbol alone; review the actual sensing and interrupting points. The project team should verify the bus configuration, normal and alternate operating states, breaker control logic, and any required interlocks against the intended scheme. If a tie can change the source or direction of current, that operating condition should be included in the engineering review. The selected lineup arrangement must match the approved protection design and specified ratings.
Coordinate Transformer Protection
Transformer protection may use more than one protective function, with choices shaped by transformer characteristics, grounding, source configuration, and coordination with upstream and downstream devices. A transformer zone should be reviewed alongside its CT locations, primary and secondary switching, grounding connections, and the equipment intended to clear a detected fault. If a differential scheme is proposed, the engineer must account for the transformer’s applicable connection and CT characteristics rather than assume that matching CT ratios alone is sufficient. Other functions may be specified for different conditions, but their use and settings require project-specific engineering. Clarify whether the transformer, protective relays, CTs, wiring, and controls are furnished in the switchgear scope or by others. The manufacturer can coordinate assembly interfaces to approved documents; relay selection, application, coordination, and final settings should be assigned to qualified project professionals.
Assign Study and Setting Duties
Before procurement, identify who provides the short-circuit, coordination, and protection studies, who selects relay functions, and who issues approved settings. Those responsibilities may sit with the owner’s engineer, a consulting engineer, or another designated project party; they should not be assumed from the equipment quote. Define the required study inputs, including available source data, transformer information, conductor details, grounding method, and operating configurations, then confirm who supplies each item. Also specify who reviews settings, performs any required commissioning checks, and records approved changes. The switchgear manufacturer needs verified design inputs to build the specified assembly, but a quote does not establish that a protection study or field service is included. Switchgear Builder Virginia manufactures new, custom medium-voltage equipment in the USA and ships nationwide. Equipment ratings, scope, and schedule remain subject to quote and project verification.
