AMERICAN BUILT. PROJECT READY.MANUFACTURER DIRECT (951) 403-5738
Switchgear cabinets arranged across a warehouse floor.

TECHNICAL GUIDES / VIRGINIA & NATIONWIDE

Shunt Trip and Undervoltage Release

New American-built power distribution equipment, engineered around your project.

ENGINEERED FOR POWER
US
Made in the USAAmerican components
✓
Project-specific standardsConfirmed for equipment type
↗
Built to moveLead time quoted by project

TECHNICAL GUIDES / MANUFACTURER DIRECT

Shunt trips and undervoltage releases can both open a circuit breaker, but they respond differently to control power. A shunt trip acts when its coil receives a command; an undervoltage release responds when its monitored supply falls below its operating threshold. That difference affects alarm design, control-power sources, restart behavior, and what operators should expect after a disturbance. For a new switchboard or switchgear project, define the intended sequence and failure response before specifying either device. Switchgear Builder Virginia manufactures new custom equipment in the USA with all-American components and nationwide shipping. Device availability, ratings, interfaces, lead times, and suitability depend on the quoted design and project verification.

Different operating principles

A shunt trip is an electrically operated accessory that opens a compatible breaker when its coil receives the specified control voltage. The initiating command may come from a control circuit or an approved protective or emergency sequence; the project documents must define that interface. An undervoltage release, also called an undervoltage trip device in some documentation, monitors a supply and causes the breaker to open when voltage falls below its specified operating range. Depending on the device and breaker arrangement, adequate voltage may also be required to keep the breaker closed or permit closing. These are not interchangeable functions: one responds to an energized trip command, while the other responds to loss or reduction of monitored voltage. Confirm the exact breaker accessory, coil or release voltage, operating limits, and wiring diagram with the equipment design before selecting either option.

Control power and interfaces

For a shunt trip, identify where control power originates, how the initiating contact is wired, and whether the intended command supplies the voltage and duration required by the selected coil. A control source that disappears during the same event that should trip the breaker may undermine the intended sequence; assess that possibility from the project-specific one-line, schematics, and control-power arrangement. For an undervoltage release, specify which voltage it monitors and how that source behaves during normal operation, transfer, or a deliberate shutdown. Review auxiliary contacts, indication, alarms, interlocks, and control-system inputs as a coordinated interface, not as assumptions based on the accessory name. The manufacturer and design team should verify compatibility with the selected breaker, control voltage, wiring, and operating sequence. Do not assume either device includes particular monitoring, reset, or signaling functions unless those details appear in the quoted configuration and approved drawings.

Failure and restart behavior

Describe failure behavior in concrete operating scenarios: loss of control power, a broken control conductor, a low-voltage event, restoration of supply, and an operator command during or after the event. A shunt-trip circuit generally needs an effective trip command and suitable coil power at the moment of operation, so the design review should ask what happens if either is unavailable. An undervoltage release is specifically tied to its monitored voltage, but the breaker’s ability to remain closed or be reclosed depends on the selected device and configuration. Neither label alone establishes whether loads restart automatically, whether a manual action is required, or how an alarm is generated. Have the responsible electrical and controls teams define a safe, documented sequence for the application, including any required reset or restart permissives. Verify those behaviors against the actual breaker and accessory documentation rather than relying on generic descriptions.

Choosing for the application

Choose a shunt trip when the required function is to open a breaker upon a defined electrical command and the design can provide a compatible, dependable control interface. Choose an undervoltage release when breaker operation must respond to the condition of a specified monitored supply, subject to the selected accessory’s documented thresholds and behavior. Some projects may need one function, another function, or a coordinated combination; that decision depends on the hazard analysis, operating sequence, and applicable project requirements. Avoid specifying both simply as extra protection: interactions can affect transfer schemes, process continuity, restart controls, and troubleshooting. Ask the engineer or equipment supplier to document the initiating condition, source of control power, monitored voltage, intended breaker state, and recovery steps. For new custom switchgear, Switchgear Builder Virginia can review these requirements during quotation; final device selection, ratings, interfaces, and configuration remain subject to design verification.

What to verify before release

Before approving drawings, check accessory part and breaker compatibility, coil or release voltage, control-power source, monitored point, terminal and wiring details, and the stated response to loss and restoration of power. Confirm whether the specification expects alarms, auxiliary status contacts, remote commands, local controls, or interlocks, and verify that each is included in the quoted design rather than inferred. Coordinate the device sequence with protective relays, transfer equipment, emergency controls, and connected loads where applicable; confirm responsibilities with the project’s qualified design professionals. Request the manufacturer’s applicable documentation and identify any inspection, testing, or approval requirements for the particular assembly and jurisdiction. Switchgear Builder Virginia builds new equipment to project requirements, with schedules and ratings confirmed by quotation and verification. Applicable low-voltage switchboards may be offered as UL 891 assemblies when appropriate; that standard does not apply to medium- or high-voltage switchgear.

Related project guides

START A CONVERSATION

Let’s build the right solution.

Tell us what you’re building, replacing or upgrading. Share the information you have now; project details and availability can be confirmed together.

PREFER TO TALK?

(951) 403-5738

Virginia projects. Nationwide delivery.

This attempts to open a draft in your configured email app; review and send it there. Browser support varies. For immediate assistance, call (951) 403-5738.

Request a quote