AMERICAN BUILT. PROJECT READY.MANUFACTURER DIRECT (951) 403-5738
Switchgear cabinets arranged across a warehouse floor.

APPLICATIONS / VIRGINIA & NATIONWIDE

Rooftop Equipment Distribution

New American-built power distribution equipment, engineered around your project.

ENGINEERED FOR POWER
US
Made in the USAAmerican components
✓
Project-specific standardsConfirmed for equipment type
↗
Built to moveLead time quoted by project

APPLICATIONS / MANUFACTURER DIRECT

Rooftop equipment distribution starts with where electrical loads sit, how power reaches them, and what the installation must withstand. Switchgear Builder Virginia manufactures new, custom switchgear in the USA using all-American components, with nationwide shipping and short lead times subject to project scope and quote. This page outlines decisions to coordinate with the project engineer before specifying equipment; final ratings, configurations, schedules, and applicable approvals require review and verification.

Map the Loads

Begin with an equipment list tied to a roof plan, not just a total building load. Identify each rooftop unit, process load, service receptacle, and planned spare circuit, then confirm its voltage, phase, overcurrent needs, and operating duty with the responsible design team. Grouping loads can simplify feeder routing, but a single distribution point may create longer branch runs or concentrate maintenance access. Separate distribution locations may shorten routes while adding equipment, feeders, and coordination points. The best arrangement depends on actual load data, available electrical capacity, and the building’s design. Record which loads are essential, intermittent, or expected to expand; those distinctions can affect circuit allocation and future space. Switchgear Builder Virginia can build new custom equipment to quoted project requirements, but ratings and circuit counts must be reviewed rather than inferred from a preliminary equipment schedule.

Assess Exposure

A rooftop location can expose electrical equipment to sun, wind-driven rain, standing water, temperature swings, dust, and corrosive contaminants. The project team should establish the actual exposure and environmental requirements before selecting an enclosure or deciding whether distribution equipment belongs outdoors, in a protected penthouse, or elsewhere. Do not assume that a general-purpose enclosure is suitable because equipment sits beneath a screen or canopy; openings, drainage, access, and prevailing weather can change the conditions. Confirm enclosure construction, material, finish, ingress protection, ventilation, and any required environmental rating with the engineer and equipment supplier. The enclosure choice may affect heat dissipation, footprint, access, and cost, so weather protection cannot be considered separately from the electrical design. Any ratings or features are project-specific options to verify. A quote should identify the requested conditions clearly, while final suitability remains subject to engineering review and applicable requirements.

Plan Feeder Routes

Trace each feeder from its source to the rooftop distribution point, noting risers, penetrations, tray or conduit paths, bends, and transitions. Route length and conductor arrangement affect voltage drop, installation effort, and the amount of roof space occupied; final conductor sizing and protection belong with the project’s electrical design. Coordinate penetrations with roofing and waterproofing details so the route does not undermine the roof assembly. Check separation from other services and confirm how equipment connections will be reached without obstructing access or maintenance. A nearby electrical room may offer a short riser but create a crowded pathway, while a more direct route can require additional structural or weatherproofing coordination. Document source, destination, routing assumptions, and any unresolved field dimensions before equipment is released for fabrication. Switchgear Builder Virginia can quote a custom new assembly against defined project information; route changes and final interface dimensions need verification.

Coordinate Structure

Rooftop distribution equipment and associated supports introduce dead load, connection points, and potential access constraints. Provide the project engineer with the proposed equipment location, footprint, weight information available from the selected configuration, and any support or anchorage requirements for review. The structural engineer should determine whether the roof framing and support design can accommodate the arrangement, including applicable project conditions such as wind or seismic forces. Avoid assuming that roof curbs, dunnage, sleepers, or existing framing are adequate without that review. Support height can affect conduit entries, drainage, service clearances, and exposure to water or debris; placement also needs to preserve required working and maintenance access. Confirm responsibility for equipment supports, anchorage details, and field measurements among the design and construction teams. Equipment dimensions, weights, connection locations, and support interfaces are subject to the selected design and quote, not generic assumptions.

Specify and Verify

A useful equipment specification brings together the one-line diagram, load schedule, available fault-current information, source details, environmental conditions, enclosure needs, connection points, access clearances, and project-specific approval requirements. For a low-voltage switchboard, UL 891 may apply where appropriate; applicability and the required assembly configuration must be confirmed for the project. Do not apply that standard to medium- or high-voltage equipment. Ask the design team to identify required inspections, tests, or approvals rather than treating them as included by default. Before release, reconcile drawings with actual site dimensions, feeder entry direction, lifting and handling constraints, and support interfaces. Switchgear Builder Virginia manufactures new custom equipment in the USA using all-American components and ships nationwide. Lead times and schedules depend on the defined scope and must be confirmed by quote; no delivery date should be assumed until it is verified.

Related project guides

START A CONVERSATION

Let’s build the right solution.

Tell us what you’re building, replacing or upgrading. Share the information you have now; project details and availability can be confirmed together.

PREFER TO TALK?

(951) 403-5738

Virginia projects. Nationwide delivery.

This attempts to open a draft in your configured email app; review and send it there. Browser support varies. For immediate assistance, call (951) 403-5738.

Request a quote