AMERICAN BUILT. PROJECT READY.MANUFACTURER DIRECT (951) 403-5738
Gray switchgear and electrical conduit in an industrial work area.

COMPARISONS / VIRGINIA & NATIONWIDE

Primary vs Secondary Selective Distribution

New American-built power distribution equipment, engineered around your project.

ENGINEERED FOR POWER
US
Made in the USAAmerican components
✓
Project-specific standardsConfirmed for equipment type
↗
Built to moveLead time quoted by project

COMPARISONS / MANUFACTURER DIRECT

Primary-selective and secondary-selective distribution both provide a way to transfer loads between sources, but they place the transfer point in different parts of the system. That choice affects transformer arrangement, switching equipment, fault-current exposure, operating sequence, and what must be coordinated with the utility. Switchgear Builder Virginia builds custom new switchgear in the USA using all-American components, with nationwide shipping and short lead times subject to project scope and quote. The comparison below is a starting point, not a substitute for reviewing the actual one-line diagram, utility conditions, and verified equipment requirements.

Where Transfer Happens

In a primary-selective arrangement, source selection occurs on the medium-voltage side, ahead of the service transformers. The switching lineup can connect a selected primary source or feeder to a transformer, subject to the utility configuration and approved operating scheme. In a secondary-selective arrangement, two transformer-fed secondary sections are connected through a tie breaker or comparable switching device. The normal lineup commonly keeps the tie open, with transfer considered when one source or transformer is unavailable. The distinction is practical: primary selection changes which upstream path supplies a transformer, while secondary selection changes whether one secondary section can receive power from the other. Neither label alone specifies the number of sources, the transfer controls, or whether transfer is automatic. Confirm these details on the one-line and in the project sequence of operation before comparing proposals.

Transformer Arrangement

Primary-selective designs often use two primary feeders arranged to serve one or more transformers through source-selecting equipment. The transformer arrangement depends on whether the project needs alternate supply to each transformer, shared feeder capacity, or another engineered scheme. Secondary-selective designs typically use two transformers, each feeding a separate low-voltage bus section, with a tie between sections. That arrangement can preserve service to selected loads after a transformer or source interruption, but only if the remaining path and equipment can carry the transferred demand. Compare normal and contingency loading, transformer impedance, voltage compatibility, and load priorities—not simply the transformer count. A second transformer does not automatically provide full redundancy, and tying sections may change available fault current. The designer should document intended normal positions, allowable transfers, and any loads that must remain isolated during an abnormal condition.

Transfer Modes And Operation

Transfer may be manual, electrically controlled, or automatic, and those terms need a defined sequence behind them. Ask what event initiates transfer, whether the alternate source is checked for acceptable conditions, how the failed source is isolated, and whether retransfer is automatic or operator-directed. For secondary-selective equipment, the control scheme must prevent an unintended parallel connection when the sources are not approved for parallel operation. Primary-side switching has its own interlocking and source-isolation requirements. In either layout, the operating sequence should address loss and restoration of voltage, control-power availability, alarms, and what happens if a breaker or switch does not operate as intended. These decisions affect controls, wiring, interlocks, and commissioning scope. Specify the required modes and permissives in the project documents; do not assume that “selective” means seamless transfer, uninterrupted service, or a particular response time.

Fault Duty And Coordination

Fault duty can differ substantially between the two arrangements, so compare calculated conditions for each permitted operating state. A secondary tie may expose a bus to contribution from both transformers when closed; the resulting duty depends on source strength, transformer impedance, conductor impedance, and the actual configuration. Primary-selective switching can also present different fault conditions depending on feeder availability and which source is connected. Obtain utility-provided source data and have the engineer evaluate protective-device ratings, interrupting capability, bus withstand, and coordination for normal and contingency modes. Do not infer a rating from voltage class, lineup appearance, or the word “selective.” If transfer changes the fault-current path, the review should include the transferred state rather than only the normal lineup. Final equipment ratings and protective settings require project-specific calculation and verification against applicable requirements and the selected components.

Choose From The One-Line

A useful comparison begins with the actual one-line diagram and utility conditions, not a preference for one architecture in isolation. Identify service voltage, source ownership and availability, transformer locations and ratings, normal bus configuration, critical loads, allowable interruption, and the intended response to a source or transformer outage. Then compare equipment footprint, cable routing, control complexity, operating procedures, maintenance access, and the verified fault-duty results. A primary-selective concept may suit a project whose source selection belongs upstream; a secondary-selective concept may suit one organized around separate transformer-fed bus sections. Those are planning considerations, not universal recommendations. Switchgear Builder Virginia can develop custom new switchgear to defined project requirements. Final configuration, ratings, transfer functions, schedule, and applicable approvals must be established and verified through the project quote and engineering review.

Related project guides

START A CONVERSATION

Let’s build the right solution.

Tell us what you’re building, replacing or upgrading. Share the information you have now; project details and availability can be confirmed together.

PREFER TO TALK?

(951) 403-5738

Virginia projects. Nationwide delivery.

This attempts to open a draft in your configured email app; review and send it there. Browser support varies. For immediate assistance, call (951) 403-5738.

Request a quote