TECHNICAL GUIDES / MANUFACTURER DIRECT
Selecting a current transformer (CT) starts with the circuit and the job the CT must perform. A useful specification identifies expected primary current, the required secondary ratio, connected burden, accuracy needs, and whether the device serves metering, protection, or both. Those inputs help define a workable design, but they do not establish a CT rating or confirm compatibility with a particular switchgear assembly. Switchgear Builder Virginia can review project requirements for a custom new-equipment build; final device selection, schedules, and ratings remain subject to quote and verification.
Define the Circuit
Start with the system’s nominal voltage, phase arrangement, conductor configuration, and the circuit location where current will be measured. Identify normal operating current and the expected range of load, including any planned capacity changes. The CT’s primary-current rating should suit the actual application rather than being chosen from a single nameplate value without context. A ratio that is too low may limit usable range, while an unnecessarily high ratio can reduce useful signal resolution for some connected devices. Provide available fault-current information and the protective device or relay data when protection is part of the scope. These inputs help reviewers assess performance and coordination needs; they do not, by themselves, prove a CT’s fault-withstand capability or suitability. Confirm whether the project requires one CT per phase, a particular mounting arrangement, or specific space and connection details.
Specify Ratio
State the desired primary-to-secondary ratio and the connected instrument or relay input requirements. Common secondary inputs and available ratios vary by device and application, so do not assume a familiar value will match the selected equipment. A ratio must translate expected primary current into a signal the connected device can use across the operating range that matters. For metering, consider the lowest and highest currents at which readings need to be meaningful, not just the circuit’s maximum load. For protection, provide the relay model or input specifications and the fault conditions used in the protection study. Ask the design team to verify ratio compatibility alongside polarity, secondary terminal arrangement, and any required taps. Where both metering and protection functions are requested, confirm whether separate CT cores or devices are needed rather than presuming one output serves every purpose.
Calculate Burden
Burden is the load connected to a CT secondary, including meters, relays, terminal blocks, and wiring. Gather the connected device inputs and the approximate one-way cable distance, conductor size, and routing details so the reviewer can account for the complete circuit. Lead resistance can affect the burden, particularly when a secondary run is long or conductors are small; evaluating only the instrument’s input can leave out a material part of the circuit. Provide the intended secondary wiring arrangement and identify any shared devices. The acceptable burden depends on the particular CT and its specified accuracy or protection performance, so a generic burden figure should not be treated as a confirmed rating. Have the complete secondary circuit checked against the selected device data. Confirm terminal and grounding details from approved project documents, and never open an energized CT secondary as a troubleshooting step.
Match Accuracy to Use
Identify whether the CT is for revenue or operational metering, indication, monitoring, or protective relaying. Each function can call for different accuracy requirements and behavior over its intended current range. Give the required accuracy class or governing project specification when known, along with the metering device or relay documentation. For metering, define the current range where measurement accuracy matters and whether the project specifies a particular class or standard. For protection, relay settings and expected fault current influence the required CT performance; class labels alone may not establish that a device will operate as intended under the project’s conditions. If one CT is expected to support more than one function, specify each connected use and ask the engineer to confirm the design. Treat any proposed class, rating, or protection performance as subject to equipment data and project verification, not as an assumed feature.
Send a Complete Schedule
A practical CT schedule records circuit identification, voltage and phase context, expected load range, primary and secondary ratio, metering or protection function, accuracy requirement, burden details, and relay or meter inputs. Include available fault-current and protection-study information where applicable, plus physical constraints such as conductor size, bus arrangement, mounting location, and terminal access. Note whether the design calls for multiple cores, separate metering and protection CTs, or specific secondary wiring. Identify which values are project requirements and which are preliminary assumptions awaiting engineering review. Switchgear Builder Virginia can use the schedule to evaluate CT integration in a custom new switchgear build, with device selection and assembly details confirmed for the quoted project. If information is incomplete, flag open items rather than filling them with guessed ratings. Final selections, availability, and schedules require verification; no lead time is established until the project is reviewed and quoted.
