TECHNICAL GUIDES / MANUFACTURER DIRECT
Selecting a voltage transformer starts with the measurement or protection task—not a catalog voltage alone. Switchgear Builder Virginia helps buyers organize the electrical, accuracy, burden, protection and installation inputs needed to define a new switchgear project. The right specification depends on the system and connected devices, so ratings, configuration, availability and schedule must be confirmed for the quoted design. Use these checks to prepare a clear request and identify details that still need engineering review.
Define the System Voltage
State the nominal system voltage and the transformer’s intended connection: phase-to-phase, phase-to-neutral, or another arrangement shown on the one-line diagram. Include system frequency, number of phases, and whether the system is grounded, ungrounded, or uses a grounding method that affects measurement. Identify the primary voltage at the actual connection point; do not substitute a bus name or upstream service value if the transformer connects elsewhere. For a medium-voltage application, provide the system’s maximum voltage and relevant insulation or withstand requirements for engineering review. The secondary voltage must match the inputs of the connected meter, relay, transducer, or control device. If existing documents disagree, flag the discrepancy rather than selecting a ratio by assumption. The final ratio, connection, and ratings require confirmation against project drawings and the equipment arrangement being quoted.
List Connected Devices
Document every device that will use the transformer secondary, including meters, protective relays, transducers, indication circuits, and any other connected instrument. Record each device’s input voltage and, when available, its manufacturer’s stated input burden and accuracy needs. Include the number of devices and how they connect; parallel loads and lead length can affect the total burden seen by the transformer. Separate measurement circuits from protection circuits when their purposes or performance requirements differ. A revenue, supervisory, or control measurement may call for different accuracy considerations than a protective function, so avoid specifying one accuracy class for every circuit without checking the device and project requirements. If a device schedule is incomplete, identify the unknowns and request confirmation from the responsible engineer or equipment supplier. This information helps evaluate a suitable transformer ratio and secondary circuit without assuming unverified performance.
Calculate Burden and Accuracy
Burden is the load connected to the transformer secondary, commonly expressed in volt-amperes at a stated power factor. To establish it, gather device burdens and account for wiring, terminals, and the actual circuit arrangement using project design data. Compare the resulting total with the transformer’s applicable burden and accuracy requirements; do not treat a nameplate burden as proof that every accuracy level is maintained under all conditions. Specify the accuracy class or performance requirement needed for each intended function, and state the conditions or standards the project requires the supplier to verify. If the connected-device list or conductor details are not settled, mark the calculation preliminary and have it reviewed before release. Excessively underspecified burden can undermine confidence in measurement; selecting capacity without regard to accuracy needs may also be an unsuitable tradeoff. Confirm the offered design against device documentation and the project’s approved requirements.
Specify Protection and Grounding
Describe the intended primary and secondary overcurrent protection, including any required fusing, protective devices, and coordination criteria shown in the project documents. Fuse selection and placement depend on the transformer, system, available fault conditions, and applicable design requirements; provide those inputs for review rather than choosing a fuse from a generic rule. State how the secondary circuit is intended to be grounded, whether a single-point ground is specified, and how the circuit is shown on the approved drawings. Identify terminal arrangements, grounding connections, and any required isolation or test provisions. Grounding and protection details should be checked as a complete circuit so that device operation, personnel protection, and measurement requirements are addressed together. Do not infer these details from a previous installation or apply field changes without qualified review. The quoted configuration and any required accessories remain subject to engineering and project verification.
Prepare the Quote Package
Provide the current one-line diagram, relevant schematics, equipment voltage and connection details, device list, burden information, required accuracy, protection and grounding notes, and any applicable project specifications. Identify the switchgear location for the transformer, space or mounting constraints, terminal access, and environmental conditions that the design must consider. Note whether the request concerns a new assembly and clearly distinguish firm requirements from open questions or preferred options. Ask the project engineer to resolve missing system data and confirm the final transformer schedule before release. Switchgear Builder Virginia manufactures new, custom switchgear with direct USA manufacturing, all-American components, short lead times, and nationwide shipping; configuration, ratings, and schedule are confirmed through quotation and verification. For applicable low-voltage switchboard assemblies, UL 891 may apply, but it does not establish a transformer’s suitability or apply to medium- or high-voltage switchgear.
