AMERICAN BUILT. PROJECT READY.MANUFACTURER DIRECT (951) 403-5738
Three switchgear cabinets on pallets, with the left cabinet door open.

TECHNICAL GUIDES / VIRGINIA & NATIONWIDE

Medium-Voltage Surge Protection

New American-built power distribution equipment, engineered around your project.

ENGINEERED FOR POWER
US
Made in the USAAmerican components
✓
Project-specific standardsConfirmed for equipment type
↗
Built to moveLead time quoted by project

TECHNICAL GUIDES / MANUFACTURER DIRECT

Medium-voltage surge protection is not a matter of choosing an arrester by system voltage alone. Its location, electrical rating, grounding path, and relationship to protected equipment all affect the design. Buyers should align the switchgear scope with the utility’s service requirements and the engineer’s protection study before equipment is specified. Switchgear Builder Virginia manufactures new custom switchgear in the USA using all-American components, with nationwide shipping. For a project quote, provide the one-line diagram, available system data, and applicable utility documents; schedules and ratings require project-specific review and verification.

Choose the Protection Point

Arrester placement should reflect which equipment needs protection and how surge energy can enter the system. Common review points include an incoming cable termination, a transformer connection, or another location identified by the engineer; the right arrangement depends on the one-line diagram and equipment layout. Putting an arrester near protected insulation can matter because the connecting leads add electrical length and may affect the voltage appearing at the equipment during a fast surge. That does not mean every compartment needs an arrester, or that one location suits every lineup. Ask the engineer to identify the protected equipment, proposed arrester positions, lead routing, and any clearances or barriers that constrain installation. The utility may specify protection at its interface, while the project engineer addresses equipment within the facility. Resolve those responsibilities before the switchgear drawings are finalized.

Verify the Arrester Rating

A nominal system-voltage label is not enough to select an arrester. The engineer needs the system’s maximum operating voltage, grounding method, and expected temporary overvoltage conditions, including how long those conditions may persist. The arrester’s continuous operating voltage and temporary-overvoltage capability must be checked against that information, alongside the protective level needed for the connected equipment. Choosing a lower rating without analysis can expose the arrester to conditions it cannot withstand; choosing a higher rating may provide less protective margin for insulation. Do not substitute a catalog example or a rating from another project for the approved design. Request the applicable arrester data and ask the engineer to document the selection basis. Switchgear Builder Virginia can review stated requirements when preparing a custom equipment scope, but final ratings remain subject to project engineering and quote verification.

Treat Grounding as Part of the Design

Surge protection depends on a deliberate path from the arrester to the system ground, not simply on the presence of a grounding conductor somewhere in the lineup. Confirm how the arrester ground terminal connects to the equipment grounding arrangement and how that arrangement interfaces with the project grounding design. System grounding also influences temporary voltage behavior during a ground fault, so the engineer needs the actual grounding configuration rather than an assumption based on voltage class. Review conductor routing, connection points, and the physical space available in the proposed enclosure. Short, direct connections may be a design objective, but final routing must also satisfy the equipment layout and approved drawings. The utility and engineer should resolve grounding details before release for manufacture. Do not treat this guide as field-work direction; changes to medium-voltage grounding or arrester connections require qualified design and work procedures.

Coordinate With Insulation and Protection

An arrester is one part of an insulation-coordination decision. The engineer should compare the arrester’s protective characteristics with the withstand levels of the transformer, cable terminations, switchgear, and other connected equipment. That review should consider the expected surge source, system configuration, and the separation between the arrester and the equipment it is intended to protect. Protective relays and overcurrent devices address different functions; an arrester does not replace fault protection or correct a mismatched protection scheme. Ask for the applicable study assumptions and confirm that the proposed equipment arrangement reflects them. If the project includes switching operations, cable transitions, or multiple connected sources, those details may affect the analysis. The final design should identify coordination responsibilities and the documents used to verify them, rather than relying on a generic statement that an arrester is included.

Confirm Scope Before Submittal

Before requesting a switchgear quote, assemble the one-line diagram, system voltage and grounding information, utility service requirements, engineer’s arrester selection, equipment insulation data, and preferred arrester locations. Flag any information that is still pending so the quote can distinguish confirmed requirements from assumptions. Also identify whether arresters are furnished as part of the switchgear scope or supplied separately, and who is responsible for installation connections and final coordination. Review drawings for compartment space, cable access, grounding terminals, and interface points before approval; a late location change can affect enclosure layout and project coordination. Switchgear Builder Virginia builds new custom switchgear in the USA with all-American components and ships nationwide. Lead time, configuration, and ratings depend on the project and must be confirmed in the quote and reviewed documents; no schedule or rating should be inferred from a general guide.

Related project guides

START A CONVERSATION

Let’s build the right solution.

Tell us what you’re building, replacing or upgrading. Share the information you have now; project details and availability can be confirmed together.

PREFER TO TALK?

(951) 403-5738

Virginia projects. Nationwide delivery.

This attempts to open a draft in your configured email app; review and send it there. Browser support varies. For immediate assistance, call (951) 403-5738.

Request a quote