AMERICAN BUILT. PROJECT READY.MANUFACTURER DIRECT (951) 403-5738
Tall switchgear cabinets on pallets, with a panel door open.

RATINGS / VIRGINIA & NATIONWIDE

347/600 V Switchgear

New American-built power distribution equipment, engineered around your project.

ENGINEERED FOR POWER
US
Made in the USAAmerican components
✓
Project-specific standardsConfirmed for equipment type
↗
Built to moveLead time quoted by project

RATINGS / MANUFACTURER DIRECT

A 347/600 V specification deserves a system check before equipment is selected. The notation commonly describes a three-phase arrangement with 600 V between phases and 347 V from phase to neutral, but the project documents, utility service, grounding method, and connected loads must confirm what is actually required. Switchgear Builder Virginia manufactures new, custom-built switchgear in the USA using all-American components, with nationwide shipping and short lead times subject to project scope and quote. Treat device compatibility and assembly availability as items to verify—not assumptions based on the voltage label.

Confirm the system

Start with the one-line diagram and service information, not just a title or equipment schedule that says “347/600 V.” Confirm nominal voltage, phase count, frequency, wire arrangement, grounding method, and whether the service is utility-fed or supplied through a transformer. In the commonly described three-phase, four-wire wye arrangement, 600 V is measured phase to phase and 347 V phase to neutral. That description does not establish the actual configuration at a particular site. Ask the engineer or utility to reconcile conflicting documents before the equipment is quoted. Also identify whether loads use phase-to-phase voltage, phase-to-neutral voltage, or both. This affects feeder planning, neutral requirements, and the equipment arrangement. A clear, approved system description reduces the risk of specifying a lineup that fits the label but not the installation.

Check devices and loads

Build a device schedule around the confirmed system voltage and the loads each device will serve. Verify breaker or fuse voltage suitability, poles, interrupting rating, trip functions, and connection details against the project fault-current study and equipment documentation. Confirm that control power, metering, surge protection, and any voltage-sensing equipment match the specified system; do not infer their compatibility from a 347/600 V heading. For phase-to-neutral loads, account for the neutral path and the intended distribution arrangement. For three-phase loads, confirm the nameplate voltage and starting or operating requirements. Device families and available configurations can differ by manufacturer, so substitutions need engineering review rather than a voltage-only comparison. Provide load schedules, drawings, and specified device requirements with the inquiry. The final selection and ratings remain subject to quote review and verification for the actual application.

Resolve utility and code basis

Verify with the serving utility whether 347/600 V service is available at the project location and what service configuration, metering, and interface requirements apply. Do not assume that a voltage used in another region or facility is offered at this site. Have the electrical engineer identify the governing jurisdiction, adopted code basis, project specifications, and any required review or approval path. Those requirements can affect equipment construction, labeling, clearances, and submittals, but they should be confirmed for the specific project rather than inferred from a general voltage designation. If utility information, drawings, or specifications disagree, resolve the discrepancy before release for manufacture. Switchgear Builder Virginia can review the stated requirements for a new custom build; schedules and configuration depend on the verified scope and quote. Utility acceptance and authority approvals must be confirmed by the responsible parties.

Define the assembly scope

Describe the lineup functions as well as the voltage: service entrance or distribution use, incoming and outgoing sections, feeder count, bus arrangement, neutral needs, space constraints, and interface points. Specify continuous current, short-circuit withstand or interrupting requirements as applicable, and environmental conditions using project documents and engineering review. These values are not established by the 347/600 V designation. Identify whether the project calls for a low-voltage switchboard or another equipment type; product terminology alone does not settle that distinction. UL 891 applies only where the specified equipment is an applicable low-voltage switchboard, and any listing or construction requirement must be verified for the offered assembly. Share approved one-lines, elevations, specifications, and device schedules so the proposed scope can be checked for gaps before quotation. Custom details and availability are confirmed project by project.

Prepare a useful inquiry

For a practical quote review, send the latest one-line diagram, load and device schedules, utility service confirmation, fault-current information, installation location, and required submittal or approval criteria. Mark unresolved items rather than filling them with assumptions, especially grounding, neutral configuration, available fault current, and whether 347 V loads are present. State whether the design requires both 347 V phase-to-neutral and 600 V phase-to-phase distribution, or simply uses the notation as a service reference. Switchgear Builder Virginia manufactures and supplies new switchgear, with direct USA manufacturing, all-American components, custom-build capability, short lead times, and nationwide shipping. These are company capabilities, not a promise of a particular configuration or delivery date. Equipment ratings, device fit, assembly availability, schedule, and any applicable UL 891 requirements must be verified against the project documents and quote.

Related project guides

START A CONVERSATION

Let’s build the right solution.

Tell us what you’re building, replacing or upgrading. Share the information you have now; project details and availability can be confirmed together.

PREFER TO TALK?

(951) 403-5738

Virginia projects. Nationwide delivery.

This attempts to open a draft in your configured email app; review and send it there. Browser support varies. For immediate assistance, call (951) 403-5738.

Request a quote