AMERICAN BUILT. PROJECT READY.MANUFACTURER DIRECT (951) 403-5738
Three gray switchgear cabinets on wooden pallets in a warehouse.

RATINGS / VIRGINIA & NATIONWIDE

Interrupting Rating

New American-built power distribution equipment, engineered around your project.

ENGINEERED FOR POWER
US
Made in the USAAmerican components
✓
Project-specific standardsConfirmed for equipment type
↗
Built to moveLead time quoted by project

RATINGS / MANUFACTURER DIRECT

Interrupting rating is one part of selecting electrical distribution equipment, not a stand-alone measure of how much fault current an entire assembly can withstand. The right comparison starts with the available fault current at the installation point, then checks each protective device and the assembled equipment against the project documents and applicable requirements. Switchgear Builder Virginia manufactures new custom switchgear in the USA using all-American components, with nationwide shipping. Actual ratings, configuration, schedule, and any required evaluations must be confirmed for the specific project before ordering.

What the Rating Means

An interrupting rating describes the fault current a circuit breaker or fuse is rated to interrupt under specified conditions. It is a device-level capability: the protective device must be able to open the circuit when current reaches a fault level within its rating and applicable voltage conditions. It does not, by itself, establish that every bus, connection, enclosure, or other part of the complete assembly can withstand the same fault. A higher number is not automatically the right choice, either. Buyers should compare the rating with the calculated available fault current at the equipment location and confirm the device’s voltage and application details. The approved equipment documents and project requirements govern selection. Because device labels and system fault calculations answer different questions, keep the interrupting rating distinct from assembly withstand or short-circuit ratings when reviewing submittals.

Start With Fault Current

Available fault current is the prospective current a power system could deliver at a particular point during a fault. Its value depends on the source and the electrical path to the equipment, so it can differ between locations in one facility. A project’s engineer or other qualified design professional should establish the applicable value and assumptions; do not select a breaker from a building-wide headline number without checking where that value applies. Buyers can help by providing the one-line diagram, system voltage, transformer and source information, and specified fault-current study or design criteria, when available. If the project documents are incomplete or conflicting, resolve that before final equipment selection. The manufacturer can review stated requirements while preparing a quote, but a quote is not a substitute for a verified system study or approval of the design.

Device Versus Assembly

A switchboard or other assembly brings multiple devices and conductive parts together. Its assembly-level short-circuit or withstand rating addresses the assembly as a whole under stated conditions; a breaker’s interrupting rating addresses that breaker’s ability to interrupt current. These figures are related, but they are not interchangeable, and the larger-looking value does not establish compliance on its own. Check the specified assembly rating, device ratings, voltage, configuration, and any conditions or limitations in the manufacturer’s documentation. Where a project depends on a tested or evaluated combination, verify that the proposed arrangement matches the applicable documentation rather than assuming that individually rated components establish the assembly rating. For applicable low-voltage switchboards, confirm whether UL 891 construction is required and applicable to the specified product. UL 891 does not apply to medium- or high-voltage switchgear.

Coordination and Selection

Protective-device coordination concerns how devices respond to faults at different points in a system. It is separate from interrupting capability: a device may have sufficient interrupting rating yet not provide the selectivity or coordination the design calls for. Conversely, coordination settings or a proposed series-rated combination must not be treated as permission to exceed device or assembly ratings. Have the design team verify coordination using the actual devices, settings, system voltage, and available fault-current data, following applicable documentation and requirements. Buyers should identify any specified coordination study, selective operation goals, or restrictions on device families early in procurement. These requirements can affect breaker selection, lineup arrangement, documentation, and review time. Do not infer a compliant combination from a product name, an isolated rating, or a preliminary equipment schedule; confirm the proposed configuration against project documents.

Information to Confirm

Before requesting or approving a quote, gather the equipment type, nominal voltage, available fault current at the point of connection, required device interrupting ratings, required assembly short-circuit rating, and relevant one-line diagram. Include the project’s stated standards, preferred or required protective devices, and any conditions identified in the fault study. Ask the design professional to resolve differences among drawings, specifications, and study results. Switchgear Builder Virginia can develop custom new equipment around verified project requirements; ratings and configurations remain subject to review and quote. Manufacturing is direct in the USA with all-American components, and lead times are project-dependent rather than fixed. Confirm the final ratings, documentation, and any applicable listing or evaluation before release. Nationwide shipping is available, but delivery timing, site readiness, and installation coordination should be established for the specific order.

Related project guides

START A CONVERSATION

Let’s build the right solution.

Tell us what you’re building, replacing or upgrading. Share the information you have now; project details and availability can be confirmed together.

PREFER TO TALK?

(951) 403-5738

Virginia projects. Nationwide delivery.

This attempts to open a draft in your configured email app; review and send it there. Browser support varies. For immediate assistance, call (951) 403-5738.

Request a quote