AMERICAN BUILT. PROJECT READY.MANUFACTURER DIRECT (951) 403-5738
Gray switchgear and electrical conduit in an industrial work area.

RATINGS / VIRGINIA & NATIONWIDE

Short-Circuit Current Rating

New American-built power distribution equipment, engineered around your project.

ENGINEERED FOR POWER
US
Made in the USAAmerican components
✓
Project-specific standardsConfirmed for equipment type
↗
Built to moveLead time quoted by project

RATINGS / MANUFACTURER DIRECT

Short-circuit current rating (SCCR) helps buyers compare an assembly’s ability to withstand fault current under specified conditions. It is not interchangeable with the interrupting rating of an individual breaker, and it cannot be selected from a generic equipment category alone. The project’s available fault current, system details, protective-device arrangement, and documented assembly rating all matter. Switchgear Builder Virginia manufactures new custom switchgear in the USA using all-American components, with nationwide shipping. For applicable low-voltage switchboards, UL 891 assemblies may be specified; applicability and ratings must be verified for the quoted configuration. The sections below explain what information to review before requesting a project-specific rating.

Short-Circuit Current Rating

An assembly’s short-circuit current rating states the maximum short-circuit current it is rated to withstand or manage under the conditions and configuration established for that equipment. Buyers should treat SCCR as an assembly-level requirement, not as a number inferred from the largest breaker installed. The documented rating applies to a defined arrangement of buses, protective devices, connections, and other components; changing that arrangement may change what rating is valid. In a quotation review, compare the specified SCCR with the equipment schedule and project documents, then confirm the proposed lineup and options are covered by the stated rating. Switchgear Builder Virginia builds new custom switchgear in the USA, and can review the requested rating as part of a project quotation. Final applicability, assembly configuration, and rating require project-specific verification; a general product description is not a rating statement.

Available Fault Current

Available fault current is the prospective current that could flow at the equipment location during a short circuit, based on the electrical system and its source conditions. The value is determined for the project, not selected by the switchgear manufacturer from a catalog description. Buyers should provide the current study or design information identifying the location, system voltage, and applicable fault-current value, along with relevant utility or source data when available. The equipment’s short-circuit rating must be appropriate for the project conditions and must be checked against the engineering documents. If system sources, transformers, generators, or other design conditions may change, ask the project engineer whether the available-fault-current assessment needs revision. This early coordination can prevent specifying a lineup around an assumed value that does not match the installation. Site-specific fault-current analysis and acceptance remain matters for the responsible project professionals.

The Limiting Component

The limiting component is the part or coordinated combination that sets the rating for the stated assembly configuration. A bus, breaker, fuse, connection, or other element can affect the overall result, but the actual constraint depends on the equipment design and the basis for its documented rating. It is tempting to compare only individual component nameplates; that can miss how the assembled system is evaluated and whether a specific protective-device combination is part of the rating. Ask for the rating associated with the complete proposed configuration and identify any conditions or component pairings that must remain unchanged. When considering options, such as alternate protective devices or a different lineup arrangement, request confirmation that the assembly rating still applies before approving the change. UL’s switchboard guidance addresses short-circuit ratings at the panelboard and switchboard level, reinforcing why component values alone do not establish an assembly rating. ([code-authorities.ul.com](https://code-authorities.ul.com/wp-content/uploads/2014/04/ul_PanelboardShortCircuitRatings2.pdf))

SCCR Versus Breaker Rating

A breaker’s interrupting rating describes its ability to interrupt a specified fault current under stated conditions. SCCR describes the short-circuit capability of the assembly or equipment configuration as a whole. These are related checks, but they answer different questions: a breaker with an interrupting rating that appears adequate does not, by itself, prove that the complete lineup has an adequate SCCR. Buyers should confirm the breaker’s applicable interrupting rating and the assembly’s documented short-circuit rating separately, then have the project’s responsible electrical professionals compare each with the system requirements. Do not assume that combining individually high-rated devices automatically establishes a particular assembly rating; coordinated or series arrangements may depend on specific tested or documented combinations. For an applicable low-voltage switchboard, request confirmation of the offered configuration and any rating conditions; UL 891 applicability must also be verified for the project. ([se.com](https://www.se.com/ca/en/download/document/0600DB0108/))

What to Confirm in a Quote

A useful quote review starts with the project’s required SCCR, available fault current at the equipment location, system voltage, and the one-line diagram or equipment schedule. Ask which proposed assembly configuration and protective-device selections correspond to the stated rating, and whether the quotation identifies conditions that must be preserved. Also flag planned changes to sources or system layout for the project engineer, since they may affect fault-current assumptions. Switchgear Builder Virginia offers custom new builds, short lead times subject to quote and verification, all-American components, and nationwide shipping; no schedule or rating should be assumed until confirmed for the actual scope. For applicable low-voltage switchboards, UL 891 assembly requirements can be specified and verified for the configuration. Review final submittals against project documents and obtain any required engineering or approval before procurement and installation. A quote discussion can clarify scope, but it does not replace the project’s fault-current analysis or code review.

Related project guides

START A CONVERSATION

Let’s build the right solution.

Tell us what you’re building, replacing or upgrading. Share the information you have now; project details and availability can be confirmed together.

PREFER TO TALK?

(951) 403-5738

Virginia projects. Nationwide delivery.

This attempts to open a draft in your configured email app; review and send it there. Browser support varies. For immediate assistance, call (951) 403-5738.

Request a quote