APPLICATIONS / MANUFACTURER DIRECT
Replacing electrical equipment where access is restricted takes more than matching the old lineup’s footprint. The route into the room, available rigging points, floor conditions, working clearances and maintenance needs can all affect the replacement plan. Switchgear Builder Virginia manufactures new, custom-built switchgear in the USA using all-American components, with nationwide shipping and short lead times subject to project review. Before approving dimensions, compare feasible section arrangements against verified site measurements and the electrical requirements. Final configuration, ratings, schedule and applicable approvals must be confirmed for the specific project.
Map the Full Route
Measure the entire path from the delivery point to the equipment room, not just the doorway. Record clear opening width and height, corridor pinch points, turns, overhead obstructions, thresholds, stairs, ramps and any door hardware that cannot be removed. Include the route’s usable width with handrails, piping or other fixed items in place. A lineup that fits the room may still be impossible to move through a narrow turn or under a low beam. Note whether the route changes between the loading area and final position, and identify which measurements are confirmed versus estimated. Photographs and a dimensioned sketch can help the project team review constraints, but they do not replace a site survey where one is needed. Keep access assumptions visible when comparing layouts; an unverified opening can drive costly redesign or handling changes.
Plan Handling and Rigging
Discuss how each section could be unloaded, moved and positioned before finalizing the lineup. The plan may depend on available lifting equipment, building access, floor capacity, overhead clearance, turning space and the location of approved rigging points. Do not assume a forklift, crane or chain hoist can reach the room or safely handle the equipment. Have qualified site and rigging personnel verify handling methods, load paths and any temporary obstructions that need removal. Ask the manufacturer to provide proposed shipping dimensions and section weights for the quoted configuration, then check that information against the route and handling plan. Section weight can vary with enclosure design and installed components, so generic estimates are not a substitute for project data. Coordinate delivery staging and placement responsibilities early; shipping nationwide does not establish that installation or rigging is included.
Compare Section Splits
When one assembled lineup cannot pass through the available route, compare configurations divided into multiple shipping sections. A split can make handling more practical, but it also introduces field joining, alignment and connection work that must be planned around the equipment design and qualified installation practices. Review where sections separate, how they will be oriented during movement, and whether the room has space to stage and reassemble them. Confirm the proposed shipping dimensions and weights for each section, including projections or removable parts that affect the route. Consider whether a different lineup arrangement can preserve the required electrical sequence while reducing the largest section’s handling envelope. The best split is not necessarily the one with the most pieces: additional sections may add coordination and assembly complexity. Have the manufacturer and project’s electrical and installation teams resolve these tradeoffs before approving drawings.
Check Layout and Access
Compare the replacement’s proposed footprint and connection arrangement with verified room dimensions and existing cable or bus locations. A close footprint match does not by itself establish that the new equipment can be connected, operated or maintained as intended. Review working space, door swing, operator access, ventilation needs where applicable, cable entry, termination access and routes for future component servicing. Determine which existing conductors or raceways may be reused only after the responsible design team confirms their condition and suitability. Keep building constraints separate from electrical requirements: moving a section or changing its orientation may solve a route problem but affect connection access or the room layout. Have the project’s qualified professionals check applicable requirements for the installation and jurisdiction. Final dimensions and ratings should follow verified electrical documents and site conditions, rather than assumptions drawn solely from the equipment being replaced.
Approve Verified Dimensions
Before releasing a custom build, reconcile the site survey, one-line diagram, equipment schedule, connection details, room layout and handling plan. Mark the source and status of critical dimensions, especially door openings, ceiling height, turning clearances, anchoring conditions and the largest shipping section. Resolve discrepancies with the responsible design team instead of relying on field guesses. Confirm the required voltage, current, interrupting and withstand characteristics, enclosure details and other project-specific ratings through the quote and engineering review; the inventory topic alone does not establish them. For applicable low-voltage switchboard assemblies, UL 891 may be relevant, but applicability and the offered configuration must be verified. Switchgear Builder Virginia can review a custom new-equipment configuration for the stated constraints. Lead time and shipping schedule depend on the quoted project and must be confirmed; no delivery date should be assumed before review.
