AMERICAN BUILT. PROJECT READY.MANUFACTURER DIRECT (951) 403-5738
Three switchgear cabinets on pallets, with the left cabinet door open.

APPLICATIONS / VIRGINIA & NATIONWIDE

Public Charging Site Distribution

New American-built power distribution equipment, engineered around your project.

ENGINEERED FOR POWER
US
Made in the USAAmerican components
✓
Project-specific standardsConfirmed for equipment type
↗
Built to moveLead time quoted by project

APPLICATIONS / MANUFACTURER DIRECT

Public charging site distribution starts with the service available at the property and the charging capacity the project needs to support. Switchgear Builder Virginia builds custom new switchgear in the USA with all-American components and ships nationwide. For applicable low-voltage switchboard assemblies, UL 891 requirements can be addressed as specified and verified for the project. Before equipment is selected, owners, designers, the serving utility, and permitting authorities should clarify who sets service requirements, owns metering, and handles approvals. The choices affect feeder arrangement, space, outdoor protection, and future expansion; final ratings and configuration require project-specific review and quotation.

Size the service

Start with the site's intended charging load, not simply the sum of charger nameplates. The electrical designer should establish which chargers may operate simultaneously, what load-management strategy is planned, and whether other building or site loads share the service. Then compare that demand with the utility's available service and project requirements. A larger service can provide room for growth, but may affect utility work, equipment footprint, and project cost; a tightly sized service can constrain later charger additions or operating flexibility. These tradeoffs depend on verified charger data, operating assumptions, and utility coordination, not a generic capacity figure. Confirm voltage, phase, fault-current information, and other service conditions with the responsible parties before specifying distribution equipment. Switchgear Builder Virginia can develop a custom new assembly to quoted requirements, with ratings and configuration subject to review and verification.

Plan charger feeders

A feeder plan determines how power reaches each charger group and how the site can isolate or maintain parts of the installation. Designers can evaluate separate feeders for individual units, grouped chargers, or charging zones, considering cable routes, distance, expected demand, protection coordination, and the consequences of an outage. More branches may improve isolation and simplify phased construction, while shared distribution can reduce equipment and feeder complexity; the right balance depends on the operating plan and applicable design requirements. Leave space and capacity for plausible expansion only after the owner identifies a realistic future phase. Feeder count, conductor sizing, protective devices, and interrupting ratings must be established by qualified project professionals using verified site and utility data. A switchboard layout should match that engineered schedule; do not assume a standard arrangement or rating from charger count alone.

Clarify meter ownership

Metering decisions can change the service arrangement, equipment layout, and responsibilities for installation and ongoing readings. Establish early whether the utility requires its own revenue meter, whether the property owner needs separate billing or usage data, and whether charger operators require additional measurement. These are different purposes and may involve separate equipment, communications, access, and approval requirements. Ask the utility and project stakeholders who furnishes, owns, installs, seals, reads, and maintains each meter; do not assume those duties fall to the switchgear manufacturer. The design team should document meter locations and any required compartments or provisions before the assembly is quoted. Metering provisions are project-specific options, not inherent features or approvals. Confirm applicable utility standards and permitting expectations directly with the responsible organizations, then align the switchgear drawings and equipment scope to the verified decisions.

Account for outdoor exposure

Public charging equipment may sit in parking areas or other exposed locations, but the actual environment varies by site. Review whether distribution equipment will be indoors, outdoors, under a canopy, or near washdown, road spray, dust, salt, or other contaminants. Also evaluate available working space, access control, vehicle clearance, drainage, sun exposure, and the planned cable-entry paths. These conditions influence enclosure selection, placement, maintenance access, and coordination with civil and electrical plans. An enclosure designation or environmental feature should be selected only after the project conditions and applicable requirements are confirmed; no rating should be inferred from the word “outdoor.” The owner and design team should specify the exposure and installation details for quotation and verification. Switchgear Builder Virginia can consider those stated requirements when developing a custom new assembly, subject to the final approved scope and equipment configuration.

Coordinate approvals

Assign responsibility for utility coordination, electrical design, permits, inspections, and field installation before procurement. The utility determines service-related requirements; the authority having jurisdiction reviews work under its process; and the owner, engineer, contractor, and charging provider each may control different project inputs. A responsibility matrix can identify who supplies load data, confirms available fault current, submits drawings, obtains approvals, and resolves design changes. Keep the equipment schedule aligned with those verified inputs, since a change in charger selection, service point, meter arrangement, or outdoor location may affect the distribution design. For applicable low-voltage switchboard assemblies, UL 891 requirements should be specified and verified for the particular assembly; this does not apply to medium- or high-voltage switchgear. Switchgear Builder Virginia manufactures new custom equipment, with ratings, schedule, and configuration subject to quotation and verification.

Related project guides

START A CONVERSATION

Let’s build the right solution.

Tell us what you’re building, replacing or upgrading. Share the information you have now; project details and availability can be confirmed together.

PREFER TO TALK?

(951) 403-5738

Virginia projects. Nationwide delivery.

This attempts to open a draft in your configured email app; review and send it there. Browser support varies. For immediate assistance, call (951) 403-5738.

Request a quote