AMERICAN BUILT. PROJECT READY.MANUFACTURER DIRECT (951) 403-5738
Three switchgear cabinets on pallets, with the left cabinet door open.

PRODUCTS / VIRGINIA & NATIONWIDE

Indoor Switchboards

New American-built power distribution equipment, engineered around your project.

ENGINEERED FOR POWER
US
Made in the USAAmerican components
✓
UL 891 assembliesFor applicable switchboards
↗
Built to moveLead time quoted by project

PRODUCTS / MANUFACTURER DIRECT

Indoor switchboards must fit the room, the installation route, and the work planned around them. Early coordination helps buyers compare layouts before walls, doors, conduit, and adjacent equipment limit choices. Confirm the proposed equipment dimensions, access path, working clearances, ventilation conditions, and applicable project requirements with the design team and authority having jurisdiction. Switchgear Builder Virginia manufactures new switchboards in the USA using all-American components, with custom builds and nationwide shipping. Available configurations, ratings, schedules, and any applicable UL 891 requirements are subject to project review and quote.

Start With the Room

Treat the equipment room as part of the switchboard design, not simply a space to fill after selection. Provide the design team with room length and width, ceiling height, door locations, columns, raised floors, and nearby pipes or ducts. Identify the intended equipment lineup and note which faces need access for operation or maintenance. The proposed switchboard dimensions and arrangement should be checked against these actual conditions before drawings are finalized. A compact lineup may preserve floor space, while a more spread-out arrangement can improve access to compartments or cable areas; the right choice depends on the installation and service plan. Ask for dimensional drawings early enough to coordinate the room layout. Final dimensions, configuration, and required clearances need review against project documents and applicable local requirements; a general product description is not a substitute for that check.

Check the Delivery Route

A switchboard that fits its final room may still be difficult to move there. Map the route from the receiving point to the equipment location, including exterior doors, corridors, elevators, turns, stairs, and temporary construction openings. Compare the narrowest passage and overhead restrictions with the proposed shipping and installation arrangement. Confirm who will coordinate unloading and placement, and whether the building schedule allows access when the equipment arrives. If the route is constrained, raise that issue before the lineup and shipping configuration are settled; the project team can evaluate feasible arrangements against the equipment design. Do not assume that a lineup can be split or reassembled in the field without manufacturer review. Request project-specific dimensions and handling information, then have the responsible installer confirm the route and equipment movement plan. Shipping nationwide is available, but transit and project timing should be addressed in the quote and coordinated with the site team.

Coordinate Working Space

Working clearances affect both room planning and the way equipment can be accessed after installation. Establish which sides are intended for normal operation, inspection, and service, then coordinate those access needs with walls, doors, other electrical equipment, storage, and permanent building features. Do not rely on a generic clearance number: requirements can depend on the equipment, voltage, installation conditions, adopted codes, and authority having jurisdiction. Have the electrical engineer and project team verify the applicable requirements for the specific site and design. Also consider door swing, removable panels, and the space needed to position tools or replacement parts, where relevant to the selected configuration. Keep these areas clear in construction and operating plans. Switchgear Builder Virginia can review project requirements for a custom new switchboard, but final layout acceptance, installation details, and code determinations remain subject to the project’s qualified professionals and applicable authorities.

Plan for Ventilation

An indoor location does not remove the need to consider heat and room conditions. Discuss the planned equipment arrangement, expected operating conditions, room ventilation, and nearby heat sources with the project’s electrical and mechanical designers. Confirm any equipment-specific environmental limits and ventilation needs from the approved design documents rather than assuming that a standard room arrangement will suit every installation. Changes to doors, louvers, partitions, or HVAC can affect the room and should be coordinated before construction. If the switchboard location is near dust, moisture, corrosive substances, or unusual ambient temperatures, identify those conditions for review; the design team can determine what requirements apply. Avoid treating ventilation as a substitute for selecting equipment appropriate to the installation. Document the room assumptions and revisit them if the lineup, room use, or building systems change. Equipment features and ratings are project-specific options to verify, not details established by the indoor designation alone.

Review Drawings and Scope

Before approving a purchase, compare the proposed equipment drawings with the electrical documents, room plan, cable entry needs, and installation responsibilities. Resolve discrepancies in dimensions, access, termination locations, and specified ratings through the project team before fabrication. Ask which tests, inspections, approvals, and documentation are included or required, and confirm their status in the quote and submittals; do not infer them from a product category. For applicable low-voltage switchboard assemblies, verify whether UL 891 is a project requirement and whether the quoted assembly meets the specified scope. Switchgear Builder Virginia manufactures new, custom switchboards in the USA with all-American components. Lead times and schedules are subject to quote and verification, so coordinate procurement dates with the project schedule rather than treating an estimate as a delivery commitment. A disciplined drawing review helps buyers align the equipment, room, and installation plan before those decisions become harder to change.

Related project guides

START A CONVERSATION

Let’s build the right solution.

Tell us what you’re building, replacing or upgrading. Share the information you have now; project details and availability can be confirmed together.

PREFER TO TALK?

(951) 403-5738

Virginia projects. Nationwide delivery.

This attempts to open a draft in your configured email app; review and send it there. Browser support varies. For immediate assistance, call (951) 403-5738.

Request a quote